Short answer: when FortiClient VPN climbs to 98% and then drops back to the login screen, your sign-in has already worked. The failure happens while FortiClient sets up the tunnel on your computer. The most common cause is IPv6 on the network you are using, especially a phone hotspot. Make Windows prefer IPv4 (or untick IPv6 on that network adapter as a quick test), update FortiClient to the current release, and restart.
A senior engineer at an engineering consultancy kept getting stuck at 98% when he connected FortiClient through his iPhone’s hotspot, while the same laptop connected fine from home. A colleague who tethered to his phone had exactly the same problem. The first time, upgrading FortiClient from an old 6.0 release to 7.4 fixed it. A few months later it came back, again only on the hotspot, and a reinstall did not help. This time the fix was to stop IPv6 being used on the laptop’s network adapter. Here is what we found and how to fix it.
Fixed by Ryan Colombo with Ellen Sawa-an at GCIT. Written up by Elliot Munro, CISO.
Symptoms
You click Connect in FortiClient VPN. Your username and password are accepted, the status climbs quickly, then it stops at:
Status: 98%
After a short wait FortiClient disconnects and returns to the login screen, sometimes with a tray notification that the “SSL VPN connection is down”. It often happens on one network only, for example a mobile hotspot or a particular home or hotel Wi-Fi, while the same laptop connects normally elsewhere. People describe this as “FortiClient stuck at 98”, “FortiClient VPN stops at 98 percent”, “FortiClient disconnects at 98%” or “FortiClient not working on hotspot”.

Affected Software
- Application: FortiClient VPN and FortiClient 6.x and 7.x (SSL-VPN connections)
- Platform: Windows 10 and Windows 11
- Related Services: FortiGate SSL VPN, mobile hotspots and home networks that hand out IPv6 addresses
Cause
The last few percent of a FortiClient connection is where the client builds the tunnel on your computer. It brings up the FortiClient virtual network adapter, applies the VPN’s IP address, routes and DNS settings, and starts passing traffic. Because the sign-in has already succeeded by then, a stop at 98% points to the computer or the network it is on, not your password.
Fortinet’s troubleshooting tip for this exact symptom lists these causes:
- IPv6 conflicts. Mobile carriers, and some home internet services, give your computer an IPv6 address. When the VPN gateway’s name resolves to both IPv4 and IPv6, or the network prefers IPv6, the tunnel setup can fail at the last step. This matches what we saw. The problem only happened on phone hotspots, and it stopped as soon as IPv6 was no longer used on the adapter.
- A missing or broken virtual adapter. If the FortiClient virtual adapter was not installed properly, sign-in completes but the connection stops at 98%. A clean reinstall usually fixes this.
- An old FortiClient version. Older releases can fail against current FortiGate firmware. Our first fix for this customer was simply upgrading from FortiClient 6.0 to 7.4.
Resolution
Step 1: Update FortiClient and restart
- Check the version under the information (i) icon in FortiClient. If it is well behind your IT team’s standard version, update it. On managed computers, ask your IT team to push the current release.
- Restart the computer after the update, then test the VPN on the network where it was failing.
- If it still stops at 98%, uninstall FortiClient, restart, reinstall the current version and set up the connection again. This replaces the virtual network adapter.
Step 2: Stop IPv6 interfering with the tunnel
Microsoft does not recommend switching IPv6 off completely. It recommends setting Windows to prefer IPv4 over IPv6 instead. Use that as the lasting fix, and use the adapter checkbox as a quick test.
- Quick test: press Windows key + R, type
ncpa.cpland press Enter. Right-click the Wi-Fi adapter you use for the hotspot, choose Properties, untick Internet Protocol Version 6 (TCP/IPv6) and click OK. You need administrator rights for this. - Reconnect FortiClient on the network that was failing. If it now connects, IPv6 was the cause.
- Lasting fix (administrators): set Windows to prefer IPv4. In an elevated Command Prompt run
reg add "HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip6\Parameters" /v DisabledComponents /t REG_DWORD /d 0x20 /f
then restart. Microsoft documents the value 0x20 as “Prefer IPv4 over IPv6”. You can then tick IPv6 on the adapter again and retest. - If your FortiClient is managed by EMS, version 7.2.5 and later can also be told to resolve the gateway to IPv4 only in the remote access profile, which fixes it for every user at once.
Step 3: Try the other tunnel transport
- Open FortiClient, click the Settings (gear) icon and unlock settings if prompted.
- Under VPN Options, change Preferred DTLS Tunnel (tick it if it is clear, or clear it if it is ticked) and reconnect.
- If FortiClient keeps switching the setting back, it is being controlled by your IT team’s FortiClient profile. Ask them to change it there.
Step 4: Check it worked
- Connect on the network that was failing and wait for the status to show VPN Connected.
- Open a shared drive or business application you normally use over the VPN to confirm traffic is flowing.
Important Notes
- 98% is not a password problem. Do not reset passwords or change group memberships for this symptom. Sign-in has already succeeded by this point.
- It can come back. In our case the client upgrade fixed it once, and IPv6 caused it again months later on the same hotspot. If it returns, check the IPv6 setting first.
- Do not change IPv6 on servers. These steps are for laptops and desktops that connect in from outside. Changing IPv6 on domain controllers or Exchange servers can break them.
- If the VPN connects but your internet drops, that is a different problem. See Fix: FortiClient VPN Drops Internet Connection.
Related Resources
- Fortinet Community: Troubleshooting Tip: SSL VPN fails at 98%
- Microsoft Learn: Configure IPv6 for advanced users (prefer IPv4 over IPv6)
- Fix: FortiClient VPN Drops Internet Connection
- Fix: FortiClient “The VPN Server May Be Unreachable” (-14)
- Fix: FortiClient “Permission Denied (-455)” and -7200 Errors
- Software we support at GCIT
If your staff struggle to connect to the office when they work from home or on the road, book a free consultation and we will help you make remote access reliable.